Journal of Powder Materials

Young-Sam Kwon

4 Articles

Characterization of Hot Isostatically Pressed Ni-Based Superalloy IN 713C: Youngmoo Kim, Eun-Pyo Kim, Seong-Taek Chunga, Seong Lee, Joon-Woong Noh, Sung Ho Lee, Young-Sam Kwon; J Korean Powder Metall Inst. 2013;20(4):264-268.; DOI: https://doi.org/10.4150/KPMI.2013.20.4.264

119 View
0 Download
1 Citations

Nickel-based superalloy IN 713C powders have been consolidated by hot isostatic pressing (HIPing). The microstructure and mechanical properties of the superalloys were investigated at the HIPing temperature ranging from 1030°C to 1230°C. When the IN 713C powder was heated above gammaprime solvus temperature (about 1180°C), the microstructure was composed of the austenitic FCC matrix phase gamma plus a variety of secondary phases, such as gammaprime precipitates in gamma matrix and MC carbides at grain boundaries. The yield and tensile strengths of HIPed specimens at room temperature were decreased while the elongation and reduction of area were increased as the processing temperature increased. At 700°C, the strength was similar regardless of HIPing temperature; however, the ductility was drastically increased with increasing the temperature. It is considered that these properties compared to those of cast products are originated from the homogeneity of microstructure obtained from a PM process.

Citations

Citations to this article as recorded by

Sintering and Microstructures of SUS 316L Powder Produced by 3D Printing Process
W.J. Kim, H.-H. Nguyen, H.Y. Kim, M.-T. Nguyen, H.S. Park, J.-C. Kim
Archives of Metallurgy and Materials.2017; 62(2): 1215. CrossRef

A Study on the Sintering Behavior of T42 High Speed Steel by Powder Injection Molding (PIM) Process: Dong-Wook Park, Hye-Seong Kim, Young-Sam Kwon, Kwon-Koo Cho, Su-Gun Lim, In-Shup Ahn; J Korean Powder Metall Inst. 2012;19(2):117-121.; DOI: https://doi.org/10.4150/KPMI.2012.19.2.117

161 View
0 Download
1 Citations

Abstract PDF

Tool steels serve a large range of applications including hot and cold workings of metals and injection mouldings of plastics or light alloys. The high speed steels (HSS) are specifically used as cutting tools and wear parts because it has high strength, wear resistance and hardness along with appreciable toughness and fatigue resistance. From the view of HSS microstructure, it can be described as metallic matrix composites formed by a ferrous with a dispersion of hard and wear resistant carbides. The experimental specimens were manufactured using the PIM with T42 powders (50~80 vol.%) and polymer (20~50 vol.%). The green parts were debinded in n-hexane solution at 60°C for 8 hours and thermal debinded at an N_2-H_2 mixed gas atmosphere for 8 hours. Specimens were sintered in high vacuum (10-5 Torr) and various temperatures.

Citations

Citations to this article as recorded by

Effects Of Process Parameters On Cu Powder Synthesis Yield And Particle Size In A Wet-Chemical Process
Y.M. Shin, J.-H. Lee
Archives of Metallurgy and Materials.2015; 60(2): 1247. CrossRef

The Characteristic Changes of Sintered WC-10Co Fabricated by PIM Method with Different Carbon Content: Sang-Dae Kang, Dong-Wook Park, Young-Sam Kwon, Kwon-Koo Cho, In-Shup Ahn; J Korean Powder Metall Inst. 2011;18(3):262-268.; DOI: https://doi.org/10.4150/KPMI.2011.18.3.262

141 View
0 Download

Abstract PDF: In order to investigate the microstructure and mechanical properties of WC-10 wt% Co insert tool alloy fabricated by PIM (Powder Injection Molding) process, the feedstock of WC-10 wt% and wax used as a kind of binder were mixed together by two blade mixer. After injection molding, the debinding process was carried out by two-steps. First, solvent extraction, in which the binder was eliminated by putting the specimen into normal hexane for 24 hrs at 60°C, and subsequently thermal debinding which was conducted at 260°C and 480°C for 6 hrs in the mixed gas of H_2/N_2, respectively. Meantime, in order to compensate the decarburization due to hydrogen, 1.2~1.8% of carbon was added to ensure the integrity of the phase. Finally, the specimens were sintered in vacuum under different temperatures, and the relative density of 99.8% and hardness of 2100 Hv can be achieved when sintered at 1380°C, even the TRS is lower than the conventional sintering process.

The Microstructural Properties Change Owing to the Sintering Condition of T42 High Speed Steel Produced by Powder Injection Molding Process: Kyoung-Rok Do, Sung-Hyun Choi, Young-Sam Kwon, Kwon-Koo Cho, In-Shup Ahn; J Korean Powder Metall Inst. 2010;17(4):312-318.; DOI: https://doi.org/10.4150/KPMI.2010.17.4.312

133 View
0 Download

Abstract PDF: High speed steels (HSS) were used as cutting tools and wear parts, because of high strength, wear resistance, and hardness together with an appreciable toughness and fatigue resistance. Conventional manufacturing process for production of components with HSS was used by casting. The powder metallurgy techniques were currently developed due to second phase segregation of conventional process. The powder injection molding method (PIM) was received attention owing to shape without additional processes. The experimental specimens were manufactured with T42 HSS powders (59 vol%) and polymer (41 vol%). The metal powders were prealloyed water-atomised T42 HSS. The green parts were solvent debinded in normal n-Hexane at 60°C for 24 hours and thermal debinded at N_2-H_2 mixed gas atmosphere for 14 hours. Specimens were sintered in N_2, H_2 gas atmosphere and vacuum condition between 1200 and 1320°C. In result, polymer degradation temperatures about optimum conditions were found at 250°C and 480°C. After sintering at N_2 gas atmosphere, maximum hardness of 310Hv was observed at 1280°C. Fine and well dispersed carbide were observed at this condition. But relative density was under 90%. When sintering at H_2 gas atmosphere, relative density was observed to 94.5% at 1200°C. However, the low hardness was obtained due to decarbonization by hydrogen. In case of sintering at the vacuum of 10-5 torr at temperature of 1240°C, full density and 550Hv hardness were obtained without precipitation of MC and M_6C in grain boundary.

Author index