- Fabrication of Fecralloy Foil Coated by Fecralloy Nanoparticles Using Electrospray Processing
-
Jung-Yeul Yun, Sang-Sun Yang, Hye-Young Koo, Hye-Moon Lee
-
J Korean Powder Metall Inst. 2011;18(6):526-531.
-
DOI: https://doi.org/10.4150/KPMI.2011.18.6.526
-
-
171
View
-
0
Download
-
5
Citations
-
 Abstract
 PDF
- Fecralloy is the promising materials for high temperature exhaust filtering system due to the excellent its oxidation resistance property. In this research, Fecralloy nanoparticles coated Fecralloy thin foil was prepared by a single nozzle electrospray system in order to increase surface area of Fecralloy foil. Fecralloy nanoparticles were fabricated by electrical wire explosion method in ethanol using Fecralloy wires as a source material. Electrospray modes with applied D.C voltages to Fecralloy colloidal solution were investigated to make a stable cone-jet mode. Coated layers with and without additional heat treatment were observed by FE-SEM (field emission-scanning electron microscope) and tape test for evaluating their adhesion to substrate were performed as well.
-
Citations
Citations to this article as recorded by  - Performance and techno-economic evaluation of a high-efficiency electrospray cyclone
Jun Su Park, Dae-Gyun Lee, Kang-San Lee, Jin-Han Kim, Jung Hoon Yoo, Hang Joo Shin, Young-Chan Choi, Young-joo Lee, YoungMin Woo, Meehye Lee, Jong Won Choi
Journal of Environmental Chemical Engineering.2024; 12(3): 112908. CrossRef - Electrospray and Thermal Treatment Process for Enhancing Surface Roughness of Fecralloy Coating Layer on a Large Sized Substrate
Hye Moon Lee, Hye Young Koo, Sangsun Yang, Dahee Park, Sooho Jung, Jung-Yeul Yun
Journal of Korean Powder Metallurgy Institute.2017; 24(1): 46. CrossRef - Alloyability of warm formed FeCrAl powder compacts
M.M. Rahman, A.A.A. Talib
Materials Today Communications.2015; 4: 42. CrossRef - Effect of Cell Size on the High Temperature Oxidation Properties of Fe-Cr-Al Powder Porous Metal Manufactured by Electro-spray Process
Jae-Sung Oh, Young-Min Kong, Byoung-Kee Kim, Kee-Ahn Lee
Journal of Korean Powder Metallurgy Institute.2014; 21(1): 55. CrossRef - Effect of Sintering Temperature on the High Temperature Oxidation of Fe-Cr-Al Powder Porous Metal Manufactured by Electrospray Process
Jae-Sung Oh, Young-Min Kong, Byoung-Kee Kim, Kee-Ahn Lee
Journal of Korean Powder Metallurgy Institute.2012; 19(6): 435. CrossRef
- Synthesis of Zr-Ti Alloy Powder by Magnesium Reduction
-
Dong-Won Lee, Geun-Tae Park, Tae-Soo Lim, Hye-Moon Lee, Ji-Hun Yu
-
J Korean Powder Metall Inst. 2011;18(4):359-364.
-
DOI: https://doi.org/10.4150/KPMI.2011.18.4.359
-
-
211
View
-
0
Download
-
2
Citations
-
Abstract
PDF
- Zr-Ti alloy powders were successfully synthesized by magnesium thermal reduction of metal chlorides. The evaporated and mixed gasses of ZrCl_4+TiCl_4 were injected to liquid magnesium and the chloride components were reduced by magnesium leading to the formation of MgCl_2. The released Zr and Ti atoms were then condensed to particle forms inside the mixture of liquid magnesium and magnesium chloride, which could be dissolved fully in post process by 1~5% HCl solution at room temperature. By the fraction-control of individually injected ZrCl_4 and TiCl_4 gasses, the final compositions of produced alloy powders were changed in the ranges of Zr-0 wt.%~20 wt.%Ti and their purity and particle size were about 99.4% and the level of several micrometers, respectively.
-
Citations
Citations to this article as recorded by - Synthesis of Vanadium Powder by Magnesiothermic Reduction
Dong Won Lee, Hak Sung Lee, Jung Yeul Yun, Young Ho Kim, Jei Pil Wang
Advanced Materials Research.2014; 1025-1026: 509. CrossRef - Extraction of Vanadium Powder by Metallothermic Reduction
Dong-Won Lee, Sang-Hyun Heo, Jong-Taek Yeom, Jei-Pil Wang
Journal of Korean Powder Metallurgy Institute.2013; 20(1): 43. CrossRef
- Fabrication of Micro Component of Metallic Nano Powder Using Polymer Mold
-
Woo-Seok Lee, Sang-Phil Kim, Hye-Moon Lee, Dong-Sik Bae, Chul-Jin Choi
-
J Korean Powder Metall Inst. 2007;14(3):202-207.
-
DOI: https://doi.org/10.4150/KPMI.2007.14.3.202
-
-
Abstract
PDF
- Novel polymer mold process for fabrication of microcomponents using metal nanopowders was developed and experimentally optimized. Polymer mold for forming green components was produced by using a hard master mold and polydimethylsiloxane (PDMS). In the preparation of metallic powder premix for the green components without any defect, 90 wt.% 17-4PH statinless steel nanopowders and 10 wt.% organic binder were mixed by a ball milling process. The green components with very clear gear shape were formed by filling the powder premix into the PDMS soft mold in surrounding at about 100°C. Cold isostatic pressing (CIP) was very potent process to decrease a porosity in the sintered microcomponent. The microgear fabricated by the improved process showed a good dimension tolerance of about 1.2%.
|
kpmi
